PreSonus R Series R65 150W Active 2-way AMT Studio Monitor
Superior transient response.
In order to dampen resonance peaks at higher frequencies, conventional dome tweeters are injected with fluid to raise their mass, sacrificing transient response time. By contrast, the custom-designed AMT tweeter in the R65 uses an incredibly thin, folded Kapton® membrane (< 0.01 mm) with an inlayed aluminum circuit functioning as the voice coil, allowing the tweeter to move at the same instant as the electric current. The resulting reactive response time provides marked clarity and superior transient reproduction.
Wide, consistent stereo image.
An unfolded AMT tweeter diaphragm provides 8 to 13 times the projection area of a traditional 1-inch dome tweeter, enabling R65 monitors to provide a much wider stereo soundstage than traditional designs. At the same time, the R65 provides a very limited vertical dispersion, which helps to reduce reflections from the ceiling and desktop that can cause phase coherence issues. Because it’s less subject to room-anomaly interference, the R65 reacts predictably and sounds consistent from room to room.
Transparent sound.
The R65 utilizes a 6.5-inch, custom-coated, woven Kevlar® low-frequency driver. This rigid cone maintains a more consistent dispersion pattern across its frequency rtesponse range. Biamped and driven by a 150W Class D amplifier—making the R series some of the most powerful monitors in their category—these monitors deliver an open, clear, and less fatiguing listening experience.
Have it your way.
You can customize the R65 in several ways. It’s available with black or blue faceplates to fit your studio décor. With balanced XLR, balanced ¼” TRS, and unbalanced RCA line-level inputs, it’s easy to feed audio to your R65 monitors from a mixer, an interface, a media player, or almost any other line-level source. And R series monitors offer user-adjustable contour features for optimizing the monitors for your mixing space. This enables full integration into any studio environment.The R65 offers a four-position Acoustic Space switch that helps to compensate for the boundary bass boost that occurs when the monitor is placed near a wall. A high-frequency driver level control helps to further mitigate room anomalies. An onboard highpass filter makes it easy to integrate a Temblor® T10 or other subwoofer into your monitor setup.
Features
Components and construction
- 2-way active AMT design provides articulate high-frequency response and wide stereo imaging
- Custom-designed, 6.8-inch, AMT ribbon tweeter responds to the subtlest waveforms and the highest frequencies
- 6.5 Kevlar® LF drivers provide transparent mid- and low-frequency reproduction for clean sound and punchy bass
- Balanced XLR and ¼-inch TRS plus unbalanced RCA inputs provide flexibility for seamless integration into any environment
User controls
- Acoustic Space settings (Linear, -1.5 dB, -3 dB, -6 dB) compensate for room placement
Power and safety
- Biamped 150W RMS (LF = 100W, HF = 50W), Class D power amplifier with switching power supply
- RF interference, output current limiting, over temperature, turn-on/off transient, and subsonic filter protection
- Energy Conservation Mode (with enable/disable) lowers standby power to <0.5W
- External mains fuse
- Internal power supply with IEC connector
Inputs | |
---|---|
1- Balanced XLR | |
1- Balanced ¼” TRS | |
1- Unbalanced RCA |
Performance | |
---|---|
Frequency Response | 45 Hz – 22 kHz |
Crossover Frequency | 2.7 kHz |
LF Amplifier Power | 100W Class D |
HF Amplifier Power | 50W Class D |
Peak SPL (@ 1 meter) | 104 dB |
LF Driver | 6.5” Kevlar® |
HF Driver Type | AMT |
Diaphragm | 6.8-inch2 (4,400 mm2) |
Equiv. Diaphragm ø | 3” (75 mm) |
Input Impedance | 20 kΩ balanced, 10 kΩ unbalanced |
SNR (typical, A-weighted) | >100 dB |
Power | |
---|---|
Factory preprogrammed | 100-120V ~50/60 Hz or 220-240V ~50/60 Hz |
Standby Power | < 0.5W |
Protection | |
---|---|
RF interference | |
Output-current limiting | |
Over-temperature | |
Turn-on/off transient | |
Subsonic filter | |
External mains fuse |
User Controls | |
---|---|
Volume Range | A-type taper |
HF Driver | Linear, +1 dB, -3 dB, -6 dB |
Highpass filter | Linear, 60 Hz, 80 Hz, 100 Hz |
Acoustic Space | Linear, -1.5 dB, -3 dB, -6 dB |
Energy Conservation Mode | On/Off/Query |
Cabinet | |
---|---|
Vinyl-laminated, medium-density fiberboard |
Physical | |
---|---|
Width | 8” (203 mm) |
Depth | 10.3” (261 mm) |
Height | 13” (328 mm) |
Weight | 14.7 lbs (6.65 kg) |
Condition | New |
---|---|
SKU | PS-R65 |
UPC | 673454004339 |