Pedaltrain Novo 18 Pedalboard with Voodoo Lab Mounting Kit, Pedal Power 2 Plus Power Supply, & Tour Case

SKU
BU-VDLMK-PP-N18TC
Pedaltrain Novo 18 Pedalboard with Voodoo Lab Mounting Kit, Pedal Power 2 Plus Power Supply, & Tour Case
Pedaltrain Novo 18 Pedalboard with Voodoo Lab Mounting Kit, Pedal Power 2 Plus Power Supply, & Tour Case
$358.00
Starting at $30/mo with .
Out of stock

Pedaltrain VDL-MK Voodoo Lab Mounting Kit

Pedaltrain VDL-MK Voodoo Lab Mount Kit is specially designed mounting brackets kits for all Voodoo Lab Pedal Power Supplies. The Pedaltrain VDL-MK Voodoo Lab Mount Kit lets you mount the power supply unit under Pedaltrain pedalboards.

Mounts all Voodoo Lab Power Supplies underneath PT-JR, PT-1, and PT-2.

Mounts all Voodoo Lab Power Supplies underneath PT-3 and PT-PRO.

 

Voodoo Lab Pedal Power 2 Plus 9V 12V 18V 24V DC Effect Pedal Power Supply

Filter, regulate, isolate, and protect! 
Pedal Power® 2 Plus does it, and does it well, because
any less will degrade your pedal’s performance. Players everywhere upgrade to Pedal Power 2 Plus because it powers what conventional power supplies can’t. Pedal Power 2 Plus is hand made in the U.S.A., comes complete with cables, detachable AC power cord, a 5-year warranty, and simply makes you sound better!

 

Isolation is more than fixing ground loops.
Ground loops cause hum, and the solution is to break the unwanted ground path. Isolation is the best way to do it. Unlike other power supplies, Pedal Power 2 Plus isolates EVERY output. This eliminates tone robbing interaction between units. Now you can properly power everything from vintage overdrives to modern digital marvels that others just can’t!
       
Proprietary balanced transformer makes it possible.
A typical transformer, like those used in a wall wart, creates a large magnetic field that causes hum in any audio path near it. Pedal Power 2 Plus uses a custom designed, ultra-low noise toroidal transformer, with separate balanced windings for every output. Now even the most sensitive pedals can be dead quiet.

Switching power supplies aren’t for everything.
What’s good for charging a cell phone is NOT good for your pedals. While digital switching power supplies are small and inexpensive, they also generate unpredictable transients and extraneous noise. Pedal Power 2 Plus uses an audiophile quality linear supply for consistently stable, clean, pure power.

 

FEATURES:

9V (x2) – High Current 9V and Line 6 Modelers 
These two outputs each deliver 250mA allowing you to run high current draw effects like the Boss DD-20 Giga Delay or Line 6 DL4 Delay Modeler. Via switches underneath the Pedal Power 2 Plus, these two outputs can be separately configured for regulated (Boss Twin Pedals) or unregulated (Line 6 Modelers) power allowing you to run both units if so desired. These outputs can also power any standard 9V effects as well.   

9V (x2) – Standard 9V With Battery Sag Control
These outputs each have an available 100mA of power, but also allow you to SAG the voltage from roughly 4V to 9V. This feature can be enabled via the bottom panel switches. The SAG control is mostly useful for transistor-based fuzz, octavia, and distortion circuits, as most modern opamp designs are minimally affected by variations in supply voltage. We recommend turning SAG off if you’re going to run digital pedals like delay, chorus, and reverb.

18V/24V – Using Custom Cables 
All of the outputs on the Pedal Power 2 Plus (and the original Pedal Power) are completely isolated allowing you to create different voltages. You can run effects like the current MXR Flanger by combining two 9V outputs to create a single 18V supply. By switching two outputs into 12V ACA mode, you can join them together to create a 24V output for powering numerous Electro-Harmonix stompboxes including the Deluxe Memory Man. 

Important!
Pedal Power 2 Plus is manufactured to operate from a specific supply voltage. There are three different models, which accept 100V, 120V, or 240V mains. All units sold in North America are for 120V only. You cannot operate a 120V Pedal Power using 240V power without the correct step down transformer. The supply voltage is marked on the bottom of the unit.

Short Circuit Protection 
Each output on the Pedal Power 2 Plus is short-circuit protected. This means that if you have a short in a power cable, or one of your pedals malfunctions, PP 2 Plus will temporarily turn off the power to that pedal. All other outputs will continue to function normally with no long-term damage.

 

Pedaltrain Novo 18 18"x14.5" Pedalboard with Tour Case

About novo 18

The Novo series is Pedaltrain’s new five-rail pedal board system. Novo means “a new beginning” in Latin. Pedaltrain’s new Novo Series is exactly that, a fresh redesign of their market-leading pedal board design. Thanks to Pedaltrain’s new modified rail system and open front design, mounting pedals and power supplies is easier than ever.  Even the smallest pedals make an incredibly strong bond with this new rail system. Novo 18’s five-rail design is perfect for players who use true-bypass switchers or need an extra rail to accommodate a variety of pedal configurations.Included with purchase is 90” of Pedaltrain’s professional grade hook-and-loop pedal fastener and plenty of zip ties for securing cables.

Novo 18 is available for purchase with Pedaltrain’s new professional-grade tour case.

Pedaltrain’s new one-size-fits-all power supply mounting brackets are available for purchase as needed. (Voodoo Lab Mounting Kit: PT-VDL-MK; Universal Mounting Kit: PT-UNI-MK).

More Information
Condition New
SKU BU-VDLMK-PP-N18TC
UPC 7010320713
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account